Home » Yard Work » Build Your Own Simple Squirrel Feeder

Build Your Own Simple Squirrel Feeder

DIY Simple Squirrel Feeder

Disclosure: The product links below may contain affiliate links. I receive a small percentage if you purchase via those links. However, this in no way changes the price for you. Also, as an Amazon Associate, I earn from qualifying purchases.

Table of Contents

Here’s a quick tutorial for a simple squirrel feeder that you can mount to a tree. If you’re a DIY enthusiast, this basic feeder design is an easy project to tackle, and very rewarding once your resident squirrels start to frequent their new food source.

This project is great because all you need is some scrap wood. I recommend using cedar due to its durability outdoors. Currently, all I have lying around is pine, which will do fine for the purposes of photography in this article. We’re actually going to build three feeders in this tutorial.

Related Articles

Squirrel Feeder Tutorial

  • DEWALT Miter Saw
  • Cedar Board For DIY Simple Squirrel Feeder
  • Squirrel Feeder Cedar Backs
  • Squirrel Feeder Backs
  • Squirrel Feeder Platforms

As you can see in Photo 1 above, I’m starting out with a scrap piece of 6’L x 12″W x 3/4″ thick board. You can make your squirrel feeder as large or as small as you want. In this tutorial, we’re going to make ours 3 1/2″ wide x 9″ long.

First, cut off a 9″ long section from your piece of scrap board. Then, with your table saw, rip this section of board into three 3 1/2″ wide pieces. (Photos 2, 3)

You can leave your three boards purely rectangle-shaped or add a bit of design like I did. Simply make 45-degree angle cuts on each corner, as shown in Photo 4.

For the squirrel feeder platforms, cut off a 3 1/4″ section from your original scrap of wood, then rip it into three 3 1/4″ square pieces. Then make the same 45-degree angle cuts on one end of the square pieces. (Photo 5)

Sanding and Building Your Squirrel Feeder

  • Building A Cedar Squirrel Feeder
  • Building A Simple Squirrel Feeder
  • DIY Cedar Squirrel Feeders

At this point, we’re finished with the saws, so before we join the feeder platform to the back, now’s a great time to sand all the wood pieces with a hand sander, if you want a nice-looking, smooth finish.

I mount the feeder platforms two inches above the bottom of the back piece. Place the feeder platform on the back piece, then drill two holes from behind the back piece into the platform. Make sure the drill bit is going in straight. Use a drill bit that is smaller in diameter than the screw itself.

Add a small bead of wood glue to the back of the feeder platform. Then re-position the platform back where it was against the back piece, and screw in your exterior screws into place. Be careful not to over-tighten the screws.

Finally, drill a hole in the center of the feeder platform, and insert a screw from the bottom. This screw is how you’ll mount your corn cobs. Then drill a hole in the top and the bottom of the back piece, for the screws that will fasten the feeder to the tree.

Time To Mount Your Squirrel Feeders!

DIY Simple Squirrel Feeders

Now all that’s left is to mount your feeders and add corn cobs! The photo above shows how the finished feeders should look. Again, be careful not to over-tighten the screws when mounting the feeders.

From start to finish, it took me about 30 minutes to build these three feeders. Quick, easy, and rewarding for the whole family, and for your squirrel friends!

Do you plan to make you some squirrel feeders? I’d love to hear about your plans in the comments below!

2 thoughts on “Build Your Own Simple Squirrel Feeder”

  1. Hello i’m going to start making the squirrel feeders like the ones that you made to sell at my local
    flea market.What would be a good price to ask for or sell at the flea market.


Leave a Comment

Your email address will not be published. Required fields are marked *